Use a string pulled taut against the fences to make sure that all posts are in alignment. Measure each time a new post is put in, using the previous post to check measurements against. Instead of finding out towards the end of installation that a hole is too deep, too shallow, or a post is out of line, always double check your work as you go. The more watery the cement mixture, the more harder it will be to keep the fence level while it is curing. For best results, pre-mix the cement in a wheelbarrow instead of pouring in powder and water separately into the hole in the ground. Use as little water as possible in mixing cement. This method is more slow-going at first, but will require less repair time later. Instead, install the first post by digging the hole and cementing the post, and use the upright post to begin measuring for the location of the second post. or 88.Ĭheck back with us soon as Part 2 of the Installation of Lattice will follow.Contrary to popular fence installation manuals, digging holes, cementing the posts, then finding out that the spacing is off when trying to install the framework is a costly no-no. Still, have installation questions? As we mentioned earlier, contact us we are always happy to help. Of course, you can order the standard sheet sizes as well. Hey, just a reminder, we manufacture custom sheet sizes too! So if you prefer to order the exact size you need for your project, we are happy to make it for you. When adding a privacy fence to the deck, you’ll either need to use the u-channel to align the lattice in the center of the post and rail or make sure you purchase the post/rails that have a riveted pocket in them to insert the lattice into. This method offers a clean finished look along the tiered sheets. You’ll notice in the picture above that the U-channel is used along the top of each lattice sheet as well. You can either screw through the channel and lattice to the post/railing or just screw through the channel to the post/railing within the framed area. The trick to using the channel with the lattice sheet in a framed space is to put the channel on the lattice sheet and then screw through the channel to the railing and post. We would suggest that you use the u-channel to attach the lattice sheet to the railing and post. The installation method for either of these options can vary.Īs you can see in the photo above, the deck railing post can be extended to support the lattice. If you don’t have a railing on your deck, you can build a privacy fence along the deck in the desired area. If you already have a rail on your deck, you can add a privacy screen to the top of the railing. Our next installation example is for adding Privacy to your deck. ![]() The lattice sheets are supported by the frame sections that are attached to the deck post. This type of installation does not need u-channel. The picture above shows the lattice framed and installed on the front side of the post. You will also need to secure the lattice sheet on the front of the post. Screw or nail through the channel to attach it to the deck boards. ![]() The channel also offers a capped look to the lattice sheet. The u-channel will help guide the lattice along the deck boards. The picture above shows the lattice on the front of the post with the use of the u-channel along the top of the lattice sheet. Don’t be overwhelmed with all the options. No need to predrill oversized holes for our lattice. You can either screw or nail through the lattice sheet to a support. ![]() You can put the lattice on the front of the support post, you can frame the lattice sheet and install on the front of the support post, use a u-channel or install the lattice without a u-channel. Ok, now on to the first installation example.ĭeck skirting has 4 common ways you can install the lattice. ![]() This will prevent the blade from chopping through the lattice sheet. Two when cutting our lattice with a circular saw, reverse the blade. This will prevent rust stains on your lattice. One use stainless steel nails or screws to secure your lattice sheets. If you have questions, please call us! Since Permalatt’s lattice can be used for so many projects there can be more than one way for installation.īefore we get into each project type we have a couple of suggestions. Please remember, you have options for your lattice installation. We’re going to share a few of our installation suggestions as well as ways our customers have installed our lattice in their projects. It seems the next topic is how to cut lattice. When you Google lattice installation you may notice the first topic is lattice skirting.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |